Vandy Vape Berserker V3 (B3) MTL RTA 24mm 6ml/2ml

B3 MTL RTA has the new base and convenient filling system. 

It has 2 types of capacity: 2ml with short tube and 6ml with long tube. 

The package contains 3 MTL drip tips. Berserker V3 MTL RTA can be easily installed and fully disassembled, which is great for beginners. 

You can also change airflow without disassembling the device. There are three airflow pipes in the package.

FEATURES:
1. New base design, convenient filling system
2. Two types of capacity: 6ml and 2ml
3. 3 MTL drip tips
4. Easy installation and fully disassembled device for beginners
5. Charge airflow without disassembling the device

Brand: Vandy Vape
Unit: 1 Set
Short Tube Size: 24mm*31.5mm
Long Tube Size: 24mm*43.5mm
Capacity: 2ml (short tube)/6ml(long tube)
Package: Gift Box

IN THE PACKAGE:
1pc B3 MTL RTA
2pc PEI Tube
2pc Drip Tip
1pc Glass Tube
1pc Accessory Bag
3pc Airflow Pipe
1pc Instruction Manual
2pc Superfine MTL Fused Clapton Coil 0.74ohm

Short review about Vandy Vape Berserker V3 (B3) MTL RTA 24mm 6ml/2ml

Vandy Vape Berserker V3 MTL RTA is the third version of the tank from Alex from VapersMD, which has collected the most successful achievements of the creators. The Berserker V3 RTA is made of stainless steel and is topped with 510 drip tips, of which there are three in the box. At the bottom, there is a glass flask, and in the kit, you will find a second one. The landing diameter is 24 mm, it will sit quietly on most modern devices.

The exterior of the Vandy Vape Berserker V3 (B3) MTL RTA 24mm 6ml/2ml is the first cardinal difference between the novelty and its predecessors - the classic cut (with massive glass) has been replaced by the "dominance" of metal. This is the prettiest and most aesthetic copy in the entire line of the Vandy Vape Berserker V3 that you can purchase online, especially in a compact version. Well, judge for yourself - strict chiselled outlines, knurling in the upper and lower parts, an abundance of metal, an updated modest logo, a thin line of glass and, of course, signature drip types. All this translates into a completely organic and "original" cigarette bow. In general, as you understand, I will note the design in the pros.

As for the dimensions - the diameter is not exactly cigarette, but we believe that the fans of the Vandy Vape Berserker V3 for the cheapest price are no strangers to this. In addition, on the contrary, this adds to the tank some confusion and organicity - 22mm may have looked stubby with this design. By the way, this is the most compact representative of the line. On the other hand, this construct has its own unpleasant features - a decent weight even in a compact design.

For the traditional set of drip types, as you know, you should thank the ideological inspirer of the project. This "fad" of Vandy Vape Berserker V3 24mm for us - lovers of cigarette puffs - is just a godsend. No wonder these drip types are “hunted” even in a separate sale. So, the equipment is again replete with "nipples" - a choice of three plastic options of different heights, but it seems that they have the same throughput. One of them is composite with a metal base in the form of radiators - it is also the highest. Landing is naturally standard - 510th - the diameter of the internal holes is about 4mm. The ruining of all pawns is comfortable, and thanks to the abundance of metal, even with the shortest specimen, the steam is not hot, and the lid almost does not heat up. There are no problems with condensate - in general, the models are already run-in and are familiar to fans of the line.

The lid, although it seems to be a massive part, in fact, is not. It is fixed in half a turn securely, with neat knurling to help it open. Under Vandy Vape Berserker V3 (B3) you can buy online with delivery has a couple of decent filling holes, which are surrounded by a small rim. If we take into account the last fact and add another one to it - the presence of a massive gasket under the lid, it becomes clear why not a single drop of slurry breaks out when clogged. The internal processing of the dome is spherical, moreover, the latter is rather small in height. Shaft diameter 4mm.

A magnifying kit of Vandy Vape Berserker V3 (B3) MTL RTA order online is also available from the box, of course, this is not bubble glass, because, as you remember, the ideological inspirer does not accept them. To increase the autonomy, a large flask and a shaft extension are provided. In this case, the capacity is literally unprecedented for cigarette makers. According to the creator, the actual value of the Vandy Vape Berserker V3 RTA buy online with delivery is even greater than the declared one and is 7 ml. In addition, here again, it is worth noting the rich equipment - "glasses" in fact as many as 4 pieces - nice, whatever one may say. I’ll immediately make a reservation - all coloured copies are plastic, while transparent ones are glass.

The deck will seem familiar to fans of the author's work, because, in fact, its construct has remained unchanged, with the exception of some nuances. We still have the same pair of racks, located on one side of the base and designed to fix one spiral. The hex screws are quite comfortable and strong, the holes for the legs are decent by cigarette standards, and the distance between the posts is again about 5mm. For cotton, small recesses are left, and the holes for feeding the latter are now not from below, but from the side. For ease of maintenance, the ring around the perimeter is removable and sits confidently, there is a key for proper installation.

By the way, about the service - in general, everything is very convenient, but there are nuances. When fixing, the screws slightly deform the spiral, therefore, it will be necessary to tighten only with the frame inserted. We remove the ring of the Vandy Vape Berserker V3 MTL RTA 24mm 6ml/2ml, fix/align the spiral, and then push the cotton - we do not cut off the tails. Next, we lift these ends up and thread a ring through them so that the cotton does not fall under them. After we cut off the ends, leaving a length of at least 3 mm from the outer border of the ring. Now we have shortened ends lying on the edge of the ring, then we simply press the tweezers on the cotton from the inside of the ring, thereby wrapping the ends up, as it were, and press it a little. The volume of cotton in the Vandy Vape Berserker V3 (B3) that crawls into a coil with a diameter of 2.5mm, the classic laying with tails / ends down - into the recesses - will not work due to the fact that the feed holes are located a little high. With this method of laying, I did not observe any leaks either during idle time or immediately after refuelling. I hope I didn’t spoil your brains too much - of course, it’s better to show this, rather than explain it in words - however, for a fairly experienced user, this moment, I believe, will be intuitively clear.

As for the airflow, it is again lower, the puff intensity is adjusted only with the help of interchangeable nozzles - we will return to them later. The rotary ring traditional for the line at the base of the atomizer has sunk into oblivion. In its place is a pair of neat small air intake holes. The kit of Vandy Vape Berserker V3 MTL RTA obtain for the best price provides 4 options for nozzles, the diameter of the inner holes of which is 0.8 / 1.2 / 1.4 / 2.0mm. As you understand, these same nozzles are positive pins and can be replaced with a hot one even without spinning the tank. This compares favourably with the novelty of its predecessors, where it was necessary to first disassemble the atomizer. However, that's not all - the pins are held inside the deck only there is no thread. They sit in the groove quite confidently, plus they are pressed against the pin of the spring-loaded 510th connector/battery when screwed onto the mod. At first, I was sceptical about this innovation, but the practice has proven the tightness of the construct. You can remove the pins even without a tool, but I would still recommend saving your nails) By the way, the outlet holes of the nozzles rise well above the plane of the bottom of the deck, so the condensate does not get there “with proper maintenance/use”.

As for the variability of the tightening of Vandy Vape Berserker V3 (B3) MTL RTA - yes, it is present. That is, to add a rather popular option of 1mm and not the "most common" diameter of 1.6mm, I am silent about 1.8mm - at higher values, I think the difference is not so critical. That is, I didn’t get the 1mm nozzle I was looking for, therefore 0.8 turned out to be too tight, and 1.2 was already too loose. At the maximum of possibilities, we have a variation of a fairly pressed, but still hookah, puff, and at a minimum, a fairly tight cigarette. Noise is average, moreover, it increases as the throughput of the nozzles increases. In the minuses, I, perhaps, will not note this, since at lower values the level is completely uncritical.

In conclusion, it remains to talk about taste transfer. The Vandy Vape Berserker V3 (B3) MTL RTA tank that you can order with delivery conveys the taste quite well - I, perhaps, even mark such a level in the pros. I will say more - in my humble opinion, this is the most delicious specimen from the berserker line, although, to be honest, I have already forgotten the old ones. I suspect that fans of the series will definitely be satisfied, but for fans of "generally recognized reference specimens" I think that it will still not be enough. On the other hand, there is naturally a "bridgehead" for experiments in terms of the height of the spiral relative to the airflow. In the setting, I focused, as always, on the TX level, since I consider this characteristic to be the most important for cigarette makers. By the way, a couple of words about him - "hit in the throat" here, I'll probably call it good enough. Of course, this is not a deadly siren 2 in this regard, but the TX is clearly felt - the level is clearly above average. And again I state - this is the most of all berserkers. The steam is quite dense, even a little heavy, but at the same time relatively dry.

Buck was a success both externally and internally. The design is excellent/original, the dimensions are compact, and the possibility of increasing the capacity is completely amazing. Inside, we find an easy-to-maintain deck and a system of interchangeable jets, which are now replaced incredibly quickly, without resorting to any tool. I can’t help but note the packaging - drip types/flasks are what many fell in love with the subject for. I will also note the taste transfer, or rather the TX level, as the most important for a tight puff.

We definitely recommend that you take a closer look at this cigarette box, moreover, both for beginners and experienced users. Well, fans of the line, I believe, this instance will especially please.

The price of the Vandy Vape Berserker V3 (B3) MTL RTA is the cheapest so you can buy it online with delivery to your country and house.